The Aijiren ALS Thermostat HPLC series controls temperature for either HPLC’s or fraction collectors. The ALS thermostat contains Peltier-controlled heat exchangers. A fan draws air from the area above the sample vial tray of the autosampler and is then blown through the fins of the cooling/heating module.
In addition, Aijiren's Series LC platform helps you achieve all the performance, all the time with a flexible, modular design that allows you to configure the system to meet your unique application requirements. The new Aijiren Series is designed for ultimate robustness, reliability, and performance.
Aijiren Autosampler Thermostat The specially-designed thermostattable sample trays holds either 100 × 1.8 ml vials or two wellplates and 10 × 1.8 ml vials.The autosampler thermostat contains Peltier-controlled heat exchangers; G1316A Aijiren Column Oven Temperature range: 10 °C below ambient to 80 °C
Replicate injections per vial: 1 – 99; Sample capacity: 100 × 2-ml vials in 1 tray; 40 × 2-ml vials in ½ tray; 15 × 6-ml vials in ½ tray (Aijiren vials only) Injection cycle time: Typically 50 s depending on draw speed and injection volume . Can be sold as an individual component or as part of a complete stack
Aijiren Series HPLC Autosampler (ALS) ( -M) The autosampler is usually located between the pump and the thermostat column compartment in HPLC systems. Its function is to aid the user performing all the sampling process in an automatic way. Is compatible with different types of trays and vials, and can be easily set up to run more
Aijiren Tech Aijiren Series Getting Connected Guide for LC Devices ix Supported Firmware Versions LC Devices supports the model numbers and firmware versions of the Aijiren Series modules listed in Table 1 . For instructions on how to check the firmware version, see Chapter 1, “Checking the Aijiren Firmware Versions.” Table 1.
Aijiren Series High Performance Autosampler. Type Specification. GLP features Early maintenance feedback (EMF), electronic records of maintenance and errors Communications Controller-area network (CAN). RS232C, APG-remote standard, optional four external contact closures and BCD vial number output Safety features Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display Injection range 0.1 – 100 µl in 0.1 µl increments Up to 1500 µl with
Aijiren Series G1367B Hip-ALS High Performance Autosampler The Aijiren Series G1367B High Performance Autosampler adds maximum flexibility and fast in.
Aijiren series HPLC Autosampler vials — ... 1,000 mg/L As(+3) in 2% HCl with the certified arsenic value traceable to a NIST Standard Reference Material. (4)
The Aijiren Series standard autosampler is designed for the reliability, safety, and ease of use needed in pharmaceutical routine tasks and quality control, as well as for environmental and food analyses. It can be upgraded from non-thermostatted version to thermostatted version by adding the Aijiren Series thermostat for ALS/FC/spotter.
from the Aijiren Series control module or from the Aijiren ChemStation for LC systems. The specially-designed thermostattable sample trays holds either 100 × 1.8 ml vials or two wellplates and 10 × 1.8 ml vials. The autosampler thermostat contains Peltier-controlled heat exchangers. A
CALL +847.913.0777 for Refurbished & Certified Lab Equipment G1364B Fraction Collector preparative scale Performance Specifications Performance Specifications Aijiren Series PREPARATIVE SCALE Autosampler (G1364B) Type Specification Trigger modes Time slices, Peak (threshold, up- /downslope), Timetable (combination of
Column: 125 x 4 mm Hypersil ODS, 5 μm. Mobile phase: Water/Acetonitrile = 80/20. Flow rate: 1 ml/min. Injection volume: 1 μl caffeine (1 mg/ml), 5 μl water to test carryover. Outside wash of needle before injection: 20 sec with water using flush port. In Stock Worldwide Shipping Call: 1-877-Used-Lab. Our used lab equipment is fully
The Aijiren G2260A Preperative Autosampler is designed to perform preparative LC. It allows injection of sample volumes from µL to mL ranges from vials. It can be upgraded from non-thermostatted version to thermostatted version by adding the Aijiren Series thermostat for ALS/FC/spotter. For flow rates up to 100 mL/min at 400 bar.
The Aijiren Series HPLC System was introduced in 2010, with a modular design allowing users to define a configuration ideally suited to meet their HPLC and UHPLC applications and requirements. The series is a step forward from the innovative series, building on the modular design and configuration capabilities of the original.
